ASTM D2238-22 PDF
Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm−1
Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm−1
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 7
- Дата публикации:
- 1 сентября 2022 г.
- Издание:
- D2238
- ICS:
- 83.080.20
SIGNIFICANCE AND USE 4.1 When interpreted with the aid of appropriate calibration data, either test method is acceptable for use to compare the total methyl contents of polyethylenes made by similar processes. Data on infrared absorption at certain other wavelengths is potentially useful for information on certain other wavelengths (7). Note 4: The bias of determination of the concentration of total alkyl groups depends on knowing the concentrations of methyl and ethyl branches present, since these branches have anomalously high absorptivities per group at 1378 cm−1 (7.25 μm). 4.2 Knowledge of total methyl groups in polyethylene, when combined with data on molecular weight and on reactive end groups such as vinyl, is potentially useful so as to lead to assignment of end-group structures and to shed light upon polymerization mechanisms. 4.3 Qualitative correlations are possible between data on total methyl groups in polyethylene with certain polymer properties such as melting point, density, stiffness, and other mechanical properties that are closely dependent on the degree of crystallinity of the polymer. 4.4 These test methods are especially suitable for research. They have not been tested for use in manufacturing control. SCOPE 1.1 These test methods cover measurement by infrared absorption spectrophotometry of the 1378 cm−1 (7.25 μm) band in polyethylene due to methyl groups. (1, 2, 3-6)2 Two test methods are covered: 1.1.1 Test Method A uses compensation with a standard sample film of known methyl content. 1.1.2 Test Method B uses compensation with a wedge of polymethylene or a polyethylene of known low methyl content. 1.2 These test methods are applicable to polyethylenes of Types I (density 0.910 to 0.925 g/cm3), II (density 0.926 to 0.940 g/cm3), and III (density 0.941 to 0.965 g/cm3). Note 1: For determination of density, see Specifications D1505. Note 2: In cases of Type III polyethylene with densities greater than 0.950 g/cm3, different results are obtained with the two test methods. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 7. Note 3: There is no known ISO equivalent to this standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Abstract
Overview
ASTM D2238-22: Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm−1 outlines procedures for measuring the absorbance of polyethylene in the infrared (IR) region due to the presence of methyl groups. Using infrared absorption spectrophotometry, the standard specifies methods for identifying and quantifying methyl content, which is crucial for polymer characterization and research. Developed by ASTM International, this standard applies to polyethylene types I, II, and III, and supports insights into polymer structure, processing history, and certain mechanical properties.
Key Topics
- Infrared Absorption Spectrophotometry: Detailed methods for measuring the absorption band at 1378 cm−1 (7.25 μm) in polyethylene related to methyl groups.
- Test Method A (Film Compensation Method): Uses a standard sample film of known methyl content for calibration and compensation.
- Test Method B (Wedge Compensation Method): Uses a wedge of polymethylene or a polyethylene sample with low methyl content as a reference.
- Applicability: Can be used for polyethylenes within specific density ranges (Type I: 0.910–0.925 g/cm³, Type II: 0.926–0.940 g/cm³, Type III: 0.941–0.965 g/cm³).
- Significance: Enables comparison of total methyl contents for polyethylenes produced via similar processes and assists in understanding polymerization mechanisms and end-group structures.
- Instrumentation: Requirements for spectrophotometer calibration, specimen preparation, and data correction are explicitly detailed to ensure method accuracy.
- Limitations: Primarily intended for research and not validated for use in routine manufacturing quality control.
Applications
The ASTM D2238-22 standard has several practical applications in polymer science, material testing, and quality assurance:
- Polymer Characterization: Determining the methyl group content provides insight into the molecular structure, branching, and polymerization behavior of polyethylene.
- Structure-Property Relationships: Correlations between methyl content and properties such as melting point, density, crystallinity, and mechanical properties can be established, which are valuable in product development and performance optimization.
- Research and Development: The test methods are especially suitable for laboratory research, helping scientists analyze and compare polyethylene samples from different sources or production methods.
- Support for Analytical Studies: Knowledge of methyl group concentration, when combined with molecular weight and end-group information, enables detailed assignment of polymer end-group structures.
- Calibration and Standardization: Assists with the standardization of measurement protocols across laboratories, supporting comparability and reliability in polyethylene analysis.
Related Standards
For comprehensive polyethylene analysis and IR spectrophotometry, the following ASTM standards are relevant:
- ASTM D883: Terminology Relating to Plastics
- ASTM D618: Practice for Conditioning Plastics for Testing
- ASTM D1505: Test Method for Density of Plastics by the Density-Gradient Technique
- ASTM E131: Terminology Relating to Molecular Spectroscopy
- ASTM E168: Practices for General Techniques of Infrared Quantitative Analysis
- ASTM E177: Practice for Use of the Terms Precision and Bias in ASTM Test Methods
- IEEE/ASTM SI-10: Standard for Use of the International System of Units (SI)
Note: There is currently no ISO equivalent to ASTM D2238-22.
By following ASTM D2238-22, laboratories and researchers ensure reliable, reproducible measurements of methyl groups in polyethylene via established IR absorbance methods, advancing knowledge in polymer chemistry and materials science.
Технические детали
- Технический комитет
- D20 - Plastics
- SKU
- ASTM D2238-22
Похожие стандарты
Другие стандарты ASTM
ASTM-TPT-47
Phase I & Phase II Environmental Site Assessment Processes
Phase I & Phase II Environmental Site Assessment Processes
ASTM-TPT-8
Phase I Environmental Site Assessment Practices For Commercial Real Estate: Phase I Site Assessment & Transac…
ASTM-TPT-1137
ASTM D975 Standard Specification for Diesel Fuel
ASTM D975 Standard Specification for Diesel Fuel
ASTM-TPT-1202
ASTM D8421 Standard Test Method for Determination of Per- and Polyfluoroalkyl Substances (PFAS) in Aqueous Ma…
ASTM D8421 Standard Test Method -- eLearning Course
ASTM-TPT-691
Microaprendizagem para D4057: Amostragem de ponto (PT)
D4057 Microlearning: Spot Sampling Portuguese
ASTM-TPT-1091
Metodo de prueba estandar D4052 de ASTM -- Curso de aprendizaje electrónico (ES)
Modulo eLearning para ASTM D4052 en espanol
ASTM ACEM20180086
Using Neutron Radiography to Quantify the Settlement of Fresh Concrete
Specifications have been implemented for concrete bridge decks in North America that restrict the use of higher slump concrete mixtures primarily because of concerns about differential settlement and…
ASTM ACEM20180041
Experimental Study of Competing Failure of Reinforced Concrete Based on the Weibull Distribution
To predict the failure lifetime of reinforced concrete, a current accelerating corrosion test was performed on concrete by simulating the environment in an area with saline soil. To study the concret…