ISO 8746:1997

Name: ISO 8746:1997 — Grooved pins with round head
SKU: ISO 8746:1997
Price: 25 EUR
Availability: InStock

Grooved pins with round head

Название (английский):

ISO 8746:1997

Grooved pins with round head

Статус документа:: Отменён
Формат:: Электронный (PDF)
Количество страниц:: 4
Дата публикации:: 6 ноября 1997 г.
Издание:: ISO IS 8746 edition 2 version 1
ICS:: 21.060.50

Тип поставки:

Full version25 €Ask AI2 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:1 рабочий день

Цена:25 €

Описание (английский):

La présente Norme internationale prescrit les caractéristiques des clous cannelés à tête ronde, à trois cannelures constantes sur toute leur longueur, débouchantes d'un côté et régulièrement espacées, de diamètre nominal, d1, de 1,4 mm à 20 mm inclus. Le matériau refoulé de chaque côté des cannelures forme un renflement dont le diamètre d2, supérieur au diamètre nominal d1, permet un ajustement serré de ces clous cannelés lorsqu'ils sont emmanchés en force dans un trou de diamètre de perçage égal au diamètre nominal du clou d1 (voir article 4).

Abstract

Похожие стандарты

Стандарты, упомянутые в описании

Overview

ISO 8746:1997 specifies the characteristics of round-head grooved pins used as fasteners. These pins have three equally spaced longitudinal grooves and nominal diameters from 1.4 mm to 20 mm inclusive. The displaced material at the grooves forms an expanded diameter larger than the nominal diameter, producing a non-positive locking fit when the pin is driven into a hole of nominal diameter (tolerance class H11).

Key characteristics in the standard include allowed materials, surface finishes, hardness for cold-heading steel, dimensional limits and designation conventions. Acceptance inspection is referenced to ISO 3269.

Key Topics

Nominal diameters: 1.4 mm to 20 mm inclusive.

Grooves: Three equally spaced longitudinal grooves; grooving angle of 70° applies to grooved pins made from steel and may be modified for other materials depending on resilience.

Expanded diameter (d2): Greater than nominal diameter (d1); testing of d2 is performed using a GO/NO-GO ring gauge as noted in the standard.

Types: Type A (chamfered end) and Type B (pilot end). Type selection can be by supplier discretion or specified by the customer.

Materials: Cold-heading steel (St) with hardness range 125 HV30 to 245 HV30 is specified; other materials may be agreed between customer and supplier.

Surface finish & coatings: Pins are normally supplied plain with protective lubricant unless otherwise specified. Preferred coatings include black oxide, phosphate conversion coatings or zinc plating with chromate. Conversion coatings referenced: ISO 9717 and ISO 4042.

Tolerances & hole fit: The mating hole diameter should equal the nominal pin diameter and conform to tolerance class H11.

Workmanship & acceptance: Pins must be free from detrimental defects; acceptance inspection follows ISO 3269.

Applications

ISO 8746 grooved pins are used where a non-positive locking fit is acceptable and simple, reliable axial retention is required. Typical applications include:

Mechanical assemblies requiring temporary or semi-permanent axial location

Components where quick assembly and standardised pin sizing ease production and supply

Use in assemblies where shear load resistance and ease of insertion are priorities

Benefits:

Interchangeability through standardised dimensions and designation

Consistent retention due to expanded diameter and groove design

Supply chain clarity by referencing ISO 8746:1997 in procurement and drawings

Related Standards

ISO 3269 - Fasteners: Acceptance inspection (acceptability procedures)

ISO 4042 - Fasteners: Electroplated coatings (surface treatment guidance)

ISO 9717 - Phosphate conversion coatings (specification of conversion coatings)

For specification, ordering and quality inspection, reference ISO 8746:1997 directly and include required type, nominal diameter and length in the designation (example: "Grooved pin ISO 8746 – 6 · 30 – St").

ISO 8746:1997

Abstract

Похожие стандарты

Overview

Key Topics

Applications

Related Standards

Технические детали

ISO 3269:2000

Fasteners — Acceptance inspection

ISO 9717:2017

Metallic and other inorganic coatings — Phosphate conversion coating of metals

ISO 4042:2022

Fasteners — Electroplated coating systems