Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis
Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis
SIGNIFICANCE AND USE 5.1 In order to be certain that the end user of analytical results obtained from using an ASTM Committee D19 test method can be confident that the values have been obtained through a competent application of the test method, a demonstration of the proficiency of the analytical system shall be performed. Appropriate proficiency is demonstrated by achievement of performance criteria derived from results of the test method collaborative study. The QC measures specified in this practice shall be included in each ASTM test method, as applicable, to ensure the quality of measurements. 5.2 In order for users of D19 test methods to achieve consistently valid results, a minimum level of QC shall be performed. This minimum level of QC is stipulated in this practice and by the task groups developing D19 test methods. If the specific requirements outlined in this practice are not applicable to the test method, alternative QC shall be defined in the test method. SCOPE 1.1 This practice provides specific, mandatory requirements for incorporating quality control (QC) procedures into all test methods under the jurisdiction of Committee D19. 1.2 ASTM International has adopted the following: Policy on implementation of requirements for a quality control section in standard test methods generated by Committee D19 on Water. GENERAL—By July 29, 1998, or at the next reapproval or revision, whichever is later, every D19 Standard Test Method shall contain a QC section that is in full compliance with the requirements of this practice. NEW COLLABORATIVE TESTING—As of July 29, 1998, each collaborative study design shall include a QC section as part of the method to be tested. Prior to approval of the study design, the Results Advisor or equivalent shall ascertain the appropriateness of the QC section in meeting the requirements of this practice and Practice D2777, and shall advise the designer of the study of any changes needed to fulfill the requirements of these practices. Before a collaborative study may be conducted, approval of the study design by the Results Advisor or equivalent shall be obtained. OLDER VALIDATED METHODS—Standard test methods that were validated using Practices D2777 – 77, D2777 – 86, or D2777 – 94, when balloted for reapproval or revision, shall contain a QC section based upon the best information from the historical record. Where appropriate, information derived from the record of the collaborative study shall be utilized for this purpose. The introduction of the QC section into these standard test methods shall not be construed as a requirement for a new collaborative study, though the Subcommittee may opt for such a study. Any information available regarding QC or precision/bias testing shall be included in the appropriate sections of the published test method. 1.3 Required QC sections in all applicable test methods are intended to achieve two goals. First, users of Committee D19 test methods will be able to demonstrate a minimum competency in the performance of these test methods by comparison with collaborative study data. Second, all users of test methods will be required to perform a minimum level of QC as part of proper implementation of these test methods to ensure ongoing competency. 1.4 This practice contains the primary requirements for QC of a specific test method. In many cases, it may be desirable to implement additional QC requirements to assure the desired quality of data. 1.5 The specific requirements in this practice may not be applicable to all test methods. These requirements may vary depending on the type of test method used as well as the analyte being determined and the sample matrix being analyzed. 1.5.1 If there are compelling reasons why any of the specific QC requirements listed in this practice are not applicable to a specific test method, these reaso...
ASTM D5847-22 is the Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis, established by ASTM International. This standard is governed by ASTM Committee D19 on Water and provides precise, mandatory requirements for embedding quality control (QC) procedures in all water analysis test methods. By outlining structured QC measures derived from collaborative studies, ASTM D5847 ensures that users and stakeholders can trust the accuracy and reliability of analytical water testing results. The requirement for consistent quality control enhances data integrity for regulatory, commercial, and research applications in water quality analysis.
ASTM D5847-22 is integral for laboratories, water utilities, environmental testing agencies, and regulatory bodies engaged in water analysis. Practical uses include:
Другие стандарты ASTM
ASTM D5847-22 is foundational for quality control in standard test methods for water analysis, ensuring credible, actionable analytical results in water quality management. For laboratories seeking ISO or regulatory accreditation, or for organizations aiming to standardize their water testing procedures, adherence to D5847 is an essential aspect of quality assurance.
Keywords: ASTM D5847-22, water analysis, quality control, laboratory accreditation, precision, bias, certified reference materials, collaborative study, method validation, water testing standards.