SIST ISO 6526:2020

Name: SIST ISO 6526:2020 — Plain bearings - Pressed bimetallic half thrust washers - Features and tolerances
SKU: SIST ISO 6526:2020
Price: 21600 RUB
Availability: InStock

Plain bearings - Pressed bimetallic half thrust washers - Features and tolerances

Название (английский):

SIST ISO 6526:2020

Plain bearings - Pressed bimetallic half thrust washers - Features and tolerances

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 12
Дата публикации:: 4 марта 2020 г.
ICS:: 21.100.10
Технический комитет:: ISEL - Mechanical elements

Тип поставки:

Full version21 600 ₽Read online 24h1 200 ₽Read online 72h1 800 ₽

Язык документа:

ruen

Срок поставки:2 раб. дн. (перевод)

Цена:21 600 ₽

Описание (английский):

ISO 6526:2017 specifies the main features and tolerances for pressed bimetallic half thrust washers having an outside diameter up to 160 mm. NOTE 1 All the linear dimensions and tolerances are expressed in millimetres. NOTE 2 The main dimensions for the half thrust washers are not the subject of this document.

Abstract

Похожие стандарты

Упомянутые в описании и другие стандарты SIST

Overview

ISO 6526:2017 specifies the features and tolerances for pressed bimetallic half thrust washers (plain bearings) with an outside diameter up to 160 mm. All linear dimensions and tolerances are expressed in millimetres. The standard defines geometric and manufacturing tolerances (diameters, heights, total thickness, lugs, grooves, fillets, chamfers, flatness), but does not prescribe main nominal dimensions or materials and makes no general specification for surface roughness.

Key topics and requirements

Scope limit: applies to pressed bimetallic half thrust washers with outside diameter ≤ 160 mm.

Units: all linear dimensions in millimetres.

General tolerances: unspecified linear dimensions ±0.25 mm; angular ±5°.

Diameter and height tolerances: specific tolerances for outside (D) and inside (d) diameters and for heights (H, F) are tabulated. Example: outside diameter tolerance is −0.25 mm for D ≤ 120 mm.

Thickness (eT): preferred total thickness values (e.g., 1.75, 2.0, 2.5, 3.0 mm) with corresponding negative tolerances and recommendations for oversizes.

Geometric relations: the difference D − d shall be greater than 7 · eT (outside minus inside diameter greater than seven times total thickness).

Locating lug: dimensions for lug width (A), lug length (E) and notch recess (JS13 per ISO 286‑2) are specified; lug may be offset to prevent incorrect assembly.

Grooves: groove width, back-wall thickness, and radial position tolerances are defined (including positional tolerances increasing with diameter).

Fillets and chamfers: maximum radii and chamfer widths for lug, joint faces and sliding surfaces; joint-face relief depth limits (≤ 30 % of total thickness) and relief angle β ≤ 30°.

Flatness: half washers must slide between parallel plates set to eT + p, with p specified by diameter range (e.g., p = 0.10 mm for D ≤ 80 mm).

Surface roughness: not specified due to material variability.

Applications

ISO 6526:2017 is used where pressed bimetallic half thrust washers serve as thrust plain bearing elements in rotating and sliding assemblies. Typical applications include:

Engine and gearbox thrust guidance

Transmission assemblies and rotating machinery

Repair, remanufacture and replacement of standard thrust washer components

SIST ISO 6526:2020

Abstract

Похожие стандарты

Overview

Key topics and requirements

Applications

Who uses this standard

Related standards

Технические детали

ISO 6526:2017

Plain bearings — Pressed bimetallic half thrust washers — Features and tolerances

ISO 286-2:2010/Cor 1:2013

Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of…

SIST EN ISO 6338:2026

Method to calculate GHG emissions at LNG plant (ISO 6338:2023)

SIST-TP CEN ISO/ASTM TR 52958:2026

Additive manufacturing of metals - Powder bed fusion (PBF) - In-situ coaxial photodiode monitoring for lack o…

SIST EN ISO 41002:2026

Facility management - Development of the facility management organization (ISO 41002:2026)

SIST EN ISO 844:2026

Rigid cellular plastics - Determination of compressive properties (ISO 844:2026)

SIST-TS CEN ISO/TS 17664-3:2026

Processing of health care products - Information to be provided by the medical device manufacturer for the pr…

SIST EN ISO 8980-4:2026

Ophthalmic optics - Uncut finished spectacle lenses - Part 4: Specifications and test methods for the propert…