EN ISO 14125:1998 PDF

Name: EN ISO 14125:1998 — Fibre-reinforced plastic composites - Determination of flexural properties (ISO 14125:1998)
SKU: EN ISO 14125:1998
Price: 65.56 EUR
Availability: InStock

Fibre-reinforced plastic composites - Determination of flexural properties (ISO 14125:1998)

Название (английский):

EN ISO 14125:1998

Fibre-reinforced plastic composites - Determination of flexural properties (ISO 14125:1998)

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 20
Дата публикации:: 1 марта 1998 г.
Издание:: CEN EN 14125 edition 1 version 1
ICS:: 83.120

Тип поставки:

Full version300 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:4 раб. дн. (перевод)

Цена:300 €

Описание (английский):

This International Standard specifies a method for determining the flexural properties of fibre-reinforced plastic composites under three-point (Method A) and four-point (Method B) loading. Standard test specimens are defined but parameters are included for alternative specimen sizes for use where appropriate. A range of testing speeds is included.

Abstract

Похожие стандарты

Стандарты, упомянутые в описании

Overview

EN ISO 14125:1998 - "Fibre-reinforced plastic composites - Determination of flexural properties (ISO 14125:1998)" specifies standardized test methods to determine flexural behaviour of fibre‑reinforced plastic composites using both three‑point (Method A) and four‑point (Method B) bending. The standard defines preferred specimen shapes and sizes, allowable alternatives, test speeds, apparatus requirements and result calculations for metrics such as flexural strength, flexural modulus and related deflection/strain values. It applies to fibre‑reinforced thermosetting and thermoplastic composites and is intended primarily for material screening and quality control rather than as a direct source of design parameters.

Key topics and technical requirements

Test methods: Three‑point and four‑point bending geometries are specified. The four‑point setup provides a constant bending moment in the inner span and typically reduces local compressive contact stresses versus three‑point bending.

Measured properties: Flexural stress (nominal), flexural strength (at maximum load), flexural modulus (chord modulus using defined strain points), deflection and related strain values.

Specimens: Preferred specimen classes and dimensions are given for different composite formats (e.g., discontinuous‑fibre thermoplastics, fabrics/mats, unidirectional laminates). Specimens may be moulded, machined from plates or taken from finished laminates.

Apparatus and accuracy:

Test machines must meet ISO 5893 requirements; load and deflection indicators typically ±1% full scale.
Loading/support member radii and span adjustments are specified to limit shear effects and avoid interlaminar shear failures.
Speeds of testing cover a range (examples in the standard include 0.5 to 500 mm/min) with defined tolerances.

Preparation and conditioning: Specimen preparation follows relevant moulding and machining standards; conditioning (standard atmospheres) is referenced.

Practical applications

Quality control (QC) of composite production batches.

Material screening and comparison during R&D for fibre‑matrix combinations (glass, carbon, aramid systems).

Failure mode assessment and verification of manufacturing consistency (laminate lay‑up, void content effects). Note: EN ISO 14125 is not intended to produce direct design parameters; differences between tensile and flexural results and shear contributions are noted in the standard.

Related standards

ISO 178 (flexural properties of unreinforced and filled plastics)

ISO 3167 (multipurpose test specimens)

ISO 5893 (test equipment)

ISO 291 (conditioning)

ASTM D790 and national EN documents are referenced for related test practice and geometry guidance

Keywords: EN ISO 14125:1998, flexural properties, fibre‑reinforced composites, three‑point bending, four‑point bending, flexural modulus, flexural strength, composite testing standard.

EN ISO 14125:1998 PDF

Abstract

Похожие стандарты

Overview

Key topics and technical requirements

Practical applications

Who uses this standard

Related standards

Технические детали

ISO 14125:1998

Fibre-reinforced plastic composites — Determination of flexural properties

ISO 5893:2019/Amd 1:2020

Rubber and plastics test equipment — Tensile, flexural and compression types (constant rate of traverse) — Sp…

ISO 14125:1998/Amd 1:2011

Fibre-reinforced plastic composites — Determination of flexural properties — Amendment 1

BS EN ISO 17892-2:2014

Geotechnical investigation and testing. Laboratory testing of soil. Determination of bulk density.

SIST EN ISO 3167:2014

Plastics - Multipurpose test specimens (ISO 3167:2014)

BS ISO 2910:2018

Cinematography. Screen luminance and chrominance for the projection of film motion pictures.