ISO 10555-3:2013 PDF
Intravascular catheters — Sterile and single-use catheters — Part 3: Central venous catheters
Intravascular catheters — Sterile and single-use catheters — Part 3: Central venous catheters
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 3
- Дата публикации:
- 6 июня 2013 г.
- Издание:
- ISO IS 10555 edition 2 version 1
- ICS:
- 11.040.25
ISO 10555-3:2013 specifies requirements for central venous catheters supplied in the sterile condition, and intended for single use.
Abstract
Overview
ISO 10555-3:2013 - "Intravascular catheters - Sterile and single-use catheters - Part 3: Central venous catheters" is an International Organization for Standardization (ISO) standard that specifies safety, performance and information requirements for central venous catheters supplied in the sterile condition and intended for single use. This second edition (2013) is part of the ISO 10555 series overseen by ISO/TC 84 (devices for administration of medicinal products and intravascular catheters).
Key topics and technical requirements
The standard focuses on specific product features and testing requirements for central venous catheters, building on the general rules in ISO 10555-1. Principal technical topics include:
- Scope and definitions
- Applies to single- or multilumen central venous catheters designed for introduction into or withdrawal from the central venous system.
- Reference to general requirements
- Catheters shall comply with ISO 10555-1 except where this part specifies different requirements (notably peak tensile force).
- Distance markings
- If provided, markings must indicate distance from the distal end.
- Distance between marks shall not exceed 5 cm; recommended 1 cm spacing on clinically critical portions to aid positioning and migration monitoring.
- Lumen markings
- Multilumen catheters must have lumen identification apparent to the user.
- Peak tensile force (soft tips)
- For tips of softer durometer or different construction up to 20 mm long, minimum peak tensile force is specified by catheter outer diameter:
- ≥0.55 and
- For tips of softer durometer or different construction up to 20 mm long, minimum peak tensile force is specified by catheter outer diameter:
Технические детали
- Технический комитет
- ISO/TC 84 - Devices for administration of medicinal products and catheters
- SKU
- ISO 10555-3:2013
Похожие стандарты
Упомянутые в описании и другие стандарты ISO
BS EN ISO 10555-1:2023
ДействующийIntravascular catheters. Sterile and single-use catheters. General requirements.
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…