ISO 10555-5:2013 PDF
Intravascular catheters — Sterile and single-use catheters — Part 5: Over-needle peripheral catheters
Intravascular catheters — Sterile and single-use catheters — Part 5: Over-needle peripheral catheters
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 10
- Дата публикации:
- 6 июня 2013 г.
- Издание:
- ISO IS 10555 edition 2 version 1
- ICS:
- 11.040.25
ISO 10555-5:2013 specifies requirements for over-needle peripheral intravascular catheters, intended for accessing the peripheral vascular system, supplied in the sterile condition and intended for single use.
Abstract
Overview
ISO 10555-5:2013 specifies requirements for over-needle peripheral intravascular catheters - sterile, single-use devices used to access the peripheral vascular system. This part of the ISO 10555 series focuses on the design, physical characteristics, testing and manufacturer information for over-needle peripheral catheters and their introducer needles.
Key topics and technical requirements
- Scope & definitions: Identifies terms such as catheter unit, needle tube, needle hub, vent fitting and flashback.
- Material and needle requirements: If steel needle tubing is used it shall comply with ISO 9626. Needle points must appear sharp and free from burrs under ×2.5 magnification and be designed to be non‑coring (Annex C describes typical geometries).
- Physical design:
- The catheter distal end must be tapered and fit closely to the needle (needle fully inserted must not let catheter extend beyond heel of bevel or be more than 1 mm away).
- Colour coding: Hubs or fittings must be colour coded per Table 1 to indicate nominal outside diameter (corresponding gauge numbers optionally listed).
- Multilumen catheters must clearly identify each lumen.
- Performance tests:
- Needle hub/tube union strength (Annex A): tensile/compressive testing - needles
Технические детали
- Технический комитет
- ISO/TC 84 - Devices for administration of medicinal products and catheters
- SKU
- ISO 10555-5:2013
Похожие стандарты
Упомянутые в описании и другие стандарты ISO
BS EN ISO 10555-1:2023
ДействующийIntravascular catheters. Sterile and single-use catheters. General requirements.
SIST EN ISO 9626:2016
ДействующийStainless steel needle tubing for the manufacture of medical devices - Requirements and test methods (ISO 962…
Overview EN ISO 9626:2016 (ISO 9626:2016) specifies requirements and test methods for rigid stainless steel needle tubing used in the manufacture of hypodermic needles and other medical devices for h…
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…