ISO 1209-1:2004 PDF
Rigid cellular plastics — Determination of flexural properties — Part 1: Basic bending test
Rigid cellular plastics — Determination of flexural properties — Part 1: Basic bending test
- Статус документа:
- Отменён
- Формат:
- Электронный (PDF)
- Количество страниц:
- 4
- Дата публикации:
- 18 июня 2004 г.
- Издание:
- ISO IS 1209 edition 2 version 1
- ICS:
- 83.100
ISO 1209-1:2004 specifies a simple method for assessing the behaviour of a bar of rigid cellular plastic under the action of three-point bending. It may be used to determine either the load for a specified deformation or the load at break. The version of the method specified uses small test specimens and does not produce pure bending. Hence it does not permit the calculation of the flexural strength or the apparent flexural modulus (modulus of elasticity). The user is referred to ISO 1209-2 for the determination of these parameters. The method is not applicable to cellular plastics in which significant crushing is observed. Numerical values should be compared only when determined on materials of similar physical properties and dimensions. The method is limited to materials of 20 mm thickness or greater.
Технические детали
- Технический комитет
- ISO/TC 61/SC 10 - Cellular plastics
- SKU
- ISO 1209-1:2004
Похожие стандарты
Другие стандарты ISO
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…
ISO/ASTM52901-17(2023)
ДействующийStandard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts
Scope 1.1 This document defines and specifies requirements for purchased parts made by additive manufacturing. 1.2 It gives guidelines for the elements to be exchanged between the customer and the pa…