ISO 13954:2025 PDF

Name: ISO 13954:2025 — Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
SKU: ISO 13954:2025
Price: 25 EUR
Availability: InStock

Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

Название (английский):

ISO 13954:2025

Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 11
Дата публикации:: 19 ноября 2025 г.
Издание:: ISO IS 13954 edition 2 version 1
ICS:: 23.040.60

Тип поставки:

Full version165 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:2 раб. дн. (перевод)

Цена:165 €

Описание (английский):

This document specifies a test method to assess ductility of the fusion joint interface of polyethylene electrofusion socket assemblies for use in pipe systems for the distribution of fluids. This method is applicable to assemblies, with nominal outside diameters greater than or equal to 90 mm.

Abstract

Похожие стандарты

Стандарты, упомянутые в описании

Overview

ISO 13954:2025 specifies a peel decohesion test method to assess the ductility of the fusion joint interface of polyethylene (PE) electrofusion socket assemblies used in pipe systems for the distribution of fluids. The method applies to electrofusion assemblies with nominal outside diameter ≥ 90 mm and characterizes joint performance by observing failure mode (brittle vs ductile) and calculating a percentage decohesion of the fused zone.

Key Topics and Requirements

Scope: Test method for PE electrofusion assemblies (OD ≥ 90 mm) to evaluate fusion joint ductility.

Test temperature: Conducted at 23 °C ± 2 °C.

Specimen preparation:

Each assembly: pipes must protrude from the socket (typically ≥ 125 mm before cutting).
Cut four strip test pieces per socket unless product standard says otherwise.
Test piece width: 25 mm or equal to the nominal pipe wall thickness (tolerances specified in the standard).
Free length L of the test piece: ≥ 75 mm.
A hole is drilled in the fitting for the shackle (diameter = E/5, minimum 3 mm).

Conditioning:

Test at least 24 h after fusion; intermediate conditioning periods before/after cutting are required (see standard for exact tolerances).

Apparatus:

Tensile-testing machine with force measurement capability (conforming guidance referenced to ISO 7500‑1).
Shackle-type link (length specified as 80 mm) and clamping jaws.

Test procedure:

Pull along specimen axis at 20–50 mm/min (dispute speed: 25 mm/min ±10%).
Continue until complete separation; record maximum breaking load and failure location.
Measure maximum brittle-failure length l in the fusion plane and overall fusion length L2.
Calculate percentage decohesion Ld = (l / L2) × 100%.

Interpretation: Compare percentage decohesion to product-specific requirements; if none exist, use Annex A guidance in ISO 13954:2025.

Applications and Who Uses It

Manufacturers of PE electrofusion fittings and pipes - quality control and product development.

Independent testing laboratories - certification, acceptance testing, and failure analysis.

Utilities and pipeline contractors - validation of fusion processes for potable water, gas and fluid distribution systems.

Standards writers and regulators - establishing performance criteria for electrofusion joints.

Useful for assessing joint ductility, identifying air pockets/non-fused areas, and verifying fusion procedures.

Related Standards

ISO 11413 - guidance for preparation of electrofusion socket joints.

ISO 7500‑1 - force measurement accuracy for tensile machines.

ISO 21751 - strip-bend test (alternative).

EN 12814‑4:2018 - alternative decohesion test methods.

Keywords: ISO 13954:2025, peel decohesion test, polyethylene electrofusion assemblies, PE electrofusion socket, percentage decohesion, fusion joint ductility, tensile-testing machine, brittle failure, ductile failure.

ISO 13954:2025 PDF

Abstract

Похожие стандарты

Overview

Key Topics and Requirements

Applications and Who Uses It

Related Standards

Технические детали

SIST EN ISO 7500-1:2018

Metallic materials - Calibration and verification of static uniaxial testing machines - Part 1: Tension/compr…

ISO 11413:1996

Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an el…

ISO 2175:1972

Title missing - Legacy paper document