ISO 15166-2:2000 PDF

Name: ISO 15166-2:2000 — Adhesives — Methods of preparing bulk specimens — Part 2: Elevated-temperature-curing one-part systems
SKU: ISO 15166-2:2000
Price: 25 EUR
Availability: InStock

Adhesives — Methods of preparing bulk specimens — Part 2: Elevated-temperature-curing one-part systems

Название (английский):

ISO 15166-2:2000

Adhesives — Methods of preparing bulk specimens — Part 2: Elevated-temperature-curing one-part systems

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 4
Дата публикации:: 7 декабря 2000 г.
Издание:: ISO IS 15166 edition 1 version 1
ICS:: 83.180

Тип поставки:

Full version60 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:1 раб. дн. (перевод)

Цена:60 €

Описание (английский):

This part of ISO 15166 describes methods for the preparation of bulk specimens of adhesives. The procedures described are suitable for elevated-temperature, one-part adhesives such as epoxies. They are not suitable for adhesives where the cure requires the evaporation of solvents or liberation of gas.

Abstract

Похожие стандарты

Стандарты, упомянутые в описании

Overview

ISO 15166-2:2000 specifies reproducible methods for preparing bulk specimens of elevated‑temperature‑curing one‑part adhesive systems (for example, many epoxy adhesives). It covers mould design, adhesive application, moulding, curing and reporting requirements for producing bulk test material representative of adhesive used in structural joints. This part does not apply to adhesives whose cure requires solvent evaporation or gas liberation.

Key topics and technical requirements

Mould construction

Two metal plates separated by a frame; plate thickness ≥ 5 mm to provide heat capacity and dimensional stability.
Copper or brass plates are suggested for thermal conduction; surfaces must prevent adhesion (PTFE film or release agent).
Frame height defines specimen thickness and must be uniform within ±0.5%; 2–3 mm is adequate for most tests.
For low‑viscosity adhesives that flow, use a continuous frame to prevent leakage.

Adhesive preparation and application

Minimise entrained air (degassing under vacuum) - consult the manufacturer about volatile loss risks.
Non‑flowing adhesives: dispense from a cartridge nozzle with continuous flow; keep nozzle immersed and move steadily (recommended nozzle angle ~30°).
Flowing adhesives: pour gently into the mould centre from a degassed container or use a continuous‑frame cartridge technique.

Moulding and curing

Close mould, apply sufficient pressure to avoid leaks, and place at 45°–90° inclination in the curing oven.
Cure according to the adhesive manufacturer’s instructions; monitor exotherms for fast, exothermic systems.
Excessive centre temperatures are unlikely for mould thickness ≤ 2 mm; for thicknesses > 3 mm install calibrated temperature probes to check internal temperature and consider lower cure temperatures with longer times and post‑cure as recommended.

Documentation

Report must include reference to ISO 15166‑2, adhesive ID (manufacturer, lot), moulding date/time, curing parameters (temperature, duration), mould/release agents, any post‑cure and storage conditions.

Applications and users

Adhesive manufacturers (materials characterization and QC)

Test laboratories and quality assurance teams preparing bulk specimens for mechanical testing

R&D engineers and formulators validating cure schedules and thermal behaviour (exotherm control)

Designers needing accurate adhesive property data for joint stress analysis

Using standardized bulk specimens enables consistent mechanical testing (uniaxial, shear) and better comparison of adhesive performance across labs and products.

Related standards

ISO 15166‑1 - Adhesives: Methods of preparing bulk specimens - Part 1: Two‑part systems

ISO 2818 - Plastics: Preparation of test specimens by machining

ISO 3167 - Plastics: Multipurpose test specimens

Keywords: ISO 15166-2, adhesives bulk specimens, elevated‑temperature‑curing, one‑part systems, epoxy specimen preparation, moulding and curing procedures.

ISO 15166-2:2000 PDF

Abstract

Похожие стандарты

Overview

Key topics and technical requirements

Applications and users

Related standards

Технические детали

BS ISO 15166-2:2000

Adhesives. Methods of preparing bulk specimens. Elevated-temperature-curing one-part systems.

ISO 15166-1:1998

Adhesives — Methods of preparing bulk specimens — Part 1: Two-part systems

BS EN ISO 2818:2019

Plastics. Preparation of test specimens by machining.

SIST EN ISO 3167:2014

Plastics - Multipurpose test specimens (ISO 3167:2014)