ISO 16049-2:2005 PDF
Air cargo equipment — Restraint straps — Part 2: Utilization guidelines and lashing calculations
Air cargo equipment — Restraint straps — Part 2: Utilization guidelines and lashing calculations
- Статус документа:
- Отменён
- Формат:
- Электронный (PDF)
- Количество страниц:
- 15
- Дата публикации:
- 7 января 2005 г.
- Издание:
- ISO IS 16049 edition 1 version 1
- ICS:
- 49.120
ISO 16049-2:2005 specifies utilization guidelines and principles to be used in strength calculation methods adequate to guarantee the effectiveness and ultimate load strength of tie-down/lashing arrangements used to restrain cargo on board civil transport aircraft during flight for either cargo loaded and tied down onto airworthiness certified air cargo pallets, themselves restrained into aircraft lower deck or main deck cargo systems meeting the requirements of ISO 8097; additional tie-down on aircraft structure when necessitated by pallet maximum gross mass or centre of gravity limits; non-unitized individual pieces of cargo, or pieces of cargo placed onto an unrestrained ("floating") pallet into either lower deck or main deck containerized cargo compartments of an aircraft; or individual pieces of load loaded in non containerized (bulk loaded) baggage or cargo compartments. ISO 16049-2:2005 is applicable to cargo tie-down/lashing arrangements using exclusively air cargo restraint straps conforming to ISO 16049-1. Its general recommendations may be used for tie-down arrangements using other means (e.g. steel cables, rope, chains, other types of straps), but under the user's responsibility as to their adequacy and the strength calculations required. ISO 16049-2:2005 is not applicable to the use of chains or other rigid devices for tie-down onto civil transport aircraft floor tracks. These devices are generally not recommended for use due to the possibility of generating excessive stresses in the aircraft structure, except where explicitly approved in the manufacturer's Authority approved Weight and Balance Manual. ISO 16049-2:2005 is intended to provide industry recognized means of complying with Airworthiness Authorities general regulations applicable to load-securing on board civil transport aircraft (see FAR/JAR Parts 25), and aircraft manufacturers Authority approved Weight and Balance Manuals for each aircraft type as specified therein. It is not the intent of ISO 16049-2:2005 to specify when restraint straps should be used, but how they should be used. It does not, under any circumstance, supersede the requirements of any of the above documents that take precedence at all times.
Технические детали
- Технический комитет
- ISO/TC 20/SC 9 - Air cargo and ground equipment
- SKU
- ISO 16049-2:2005
Похожие стандарты
Другие стандарты ISO
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…
ISO/ASTM52901-17(2023)
ДействующийStandard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts
Scope 1.1 This document defines and specifies requirements for purchased parts made by additive manufacturing. 1.2 It gives guidelines for the elements to be exchanged between the customer and the pa…