ISO 18314-3:2022 PDF
Analytical colorimetry — Part 3: Special indices
Analytical colorimetry — Part 3: Special indices
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 6
- Дата публикации:
- 21 ноября 2022 г.
- Издание:
- ISO IS 18314 edition 2 version 1
- ICS:
- 87.060.10
This document specifies different methods of calculating special indices, which are generally used to describe lightness respectively jetness of samples including chroma or hue within one colour-coordinate. This document is applicable to tristimulus values and chromaticity coordinates calculated using colour-matching functions of the standard colorimetric system of the CIE 1931 (2°) or CIE 1964 (10°). It is used for the specification of colour stimuli perceived as belonging to a reflecting or transmitting object where a one-dimensional value is required.
Abstract
Overview
ISO 18314-3:2022 - Analytical colorimetry - Part 3: Special indices defines standardized methods to calculate one‑dimensional colour indices used to describe lightness/jetness and chromatic shifts (chroma/hue) within a single colour coordinate. It applies to tristimulus values and chromaticity coordinates derived from the standard CIE colorimetric systems (CIE 1931 2° and CIE 1964 10° observers) and is intended for specifying reflecting or transmitting colour stimuli where a single index is required.
Key topics and technical requirements
- Scope and input data
- Indices are calculated from tristimulus values X, Y, Z or chromaticity x, y using CIE 1931 (2°) or CIE 1964 (10°) colour‑matching functions.
- Standard illuminant D65 is used for parameters in several indices.
- Defined special indices
- CIE whiteness index (W): formula uses chromaticity offsets with parameters x and y given for D65 (values provided for 2° and 10° observers).
- Yellowness index (YI): linear combination of X and Z relative to Y with parameters a and b specified for 2° and 10° observers (follows ASTM E313 practice).
- Blackness values (M, M_C): hue‑independent and hue‑dependent blackness expressed as logarithmic functions of Y or combinations of X, Z, Y (DIN 55979 references). Absolute hue contribution dM quantifies blue vs. brown bias.
- Greyness values (G, G_C): analogous hue‑independent and hue‑dependent measures for grey admixture; absolute contribution dG describes hue bias.
- Flop‑index (FI): characterizes angular variation of lightness for near‑neutral metallic shades using specified CIELAB L*(ε) at aspecular angles (ε = 15°, 45°, 110°).
- Measurement and metrology guidance
- Recommendation for spectral photometer with 45°:0° (or 0°:45°) geometry; standard D65‑like artificial illumination for visual assessments.
- Repeatability requirement example: variance of standard Y shall be
Технические детали
- Технический комитет
- ISO/TC 256 - Pigments, dyestuffs and extenders
- SKU
- ISO 18314-3:2022
Похожие стандарты
Другие стандарты ISO
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…
ISO/ASTM52901-17(2023)
ДействующийStandard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts
Scope 1.1 This document defines and specifies requirements for purchased parts made by additive manufacturing. 1.2 It gives guidelines for the elements to be exchanged between the customer and the pa…