ISO 18319-2:2022 PDF
Fibre reinforced polymer (FRP) reinforcement for concrete structures — Part 2: Specifications of CFRP strips
Fibre reinforced polymer (FRP) reinforcement for concrete structures — Part 2: Specifications of CFRP strips
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 6
- Дата публикации:
- 17 января 2022 г.
- Издание:
- ISO IS 18319 edition 1 version 1
- ICS:
- 83.120
This document specifies requirements for unidirectional carbon fibre-reinforced polymer (CFRP) strips as external-bonded reinforcements on the concrete substrate. This document is applicable for the CFRP strips that: — consist of carbon fibre and thermoset resin; — are manufactured by pultrusion method; — have a carbon fibre fraction over 60 % by volume; and — have a thickness within 3 mm. This document specifies the methodologies to express the mechanical properties as characteristic values, appearance and dimensions, and sampling test.
Abstract
Overview
ISO 18319-2:2022 defines specifications for unidirectional carbon fibre‑reinforced polymer (CFRP) strips used as external‑bonded reinforcement on concrete structures. The standard applies to CFRP strips that: consist of carbon fibre and thermoset resin, are manufactured by the pultrusion method, have a carbon‑fibre fraction > 60% by volume, and a thickness ≤ 3 mm. It provides requirements and methods for expressing mechanical properties as characteristic values, appearance and dimensional tolerances, straightness, and sampling tests.
Key topics and requirements
- Scope and materials: Unidirectional CFRP strips with thermoset resin, pultruded manufacture, >60% carbon fibre by volume, thickness within 3 mm.
- Appearance: Strips must be free from visible defects such as cracks, whitening (incomplete curing), and blistering.
- Dimensions & tolerances:
- Nominal width, thickness, cross‑sectional area and length are agreed between parties.
- Thickness tolerance: ±10% of nominal.
- Width and cross‑sectional area shall be no less than nominal (see standard for complete table).
- Length tolerances vary by nominal length (detailed bands for l ≥ 30 m, 30–10 m, 10–5 m,
Технические детали
- Технический комитет
- ISO/TC 71/SC 6 - Non-traditional reinforcing materials for concrete structures
- SKU
- ISO 18319-2:2022
Похожие стандарты
Другие стандарты ISO
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…
ISO/ASTM52901-17(2023)
ДействующийStandard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts
Scope 1.1 This document defines and specifies requirements for purchased parts made by additive manufacturing. 1.2 It gives guidelines for the elements to be exchanged between the customer and the pa…