ISO 19403-3:2024 PDF
Paints and varnishes — Wettability — Part 3: Determination of the surface tension of liquids using the pendant drop method
Paints and varnishes — Wettability — Part 3: Determination of the surface tension of liquids using the pendant drop method
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 11
- Дата публикации:
- 4 сентября 2024 г.
- Издание:
- ISO IS 19403 edition 2 version 1
- ICS:
- 87.040
This document specifies a test method to measure the surface tension of liquids with an optical method using the pendant drop. The method can be applied for the characterization of liquid coating materials. If applied to liquids with non-Newtonian flow behaviour (as defined in ISO 3219-1:2021, 3.22), restrictions can apply. NOTE For other methods to determine the surface tension, see e.g. EN 14370 and ISO 1409.
Abstract
Overview
ISO 19403-3:2024 - Paints and varnishes - Wettability - Part 3 specifies an optical test method to determine the surface tension of liquids using the pendant drop method. The standard defines how to form and analyse a pendant drop with a drop contour analysis system and to calculate surface tension from the drop shape via the Young–Laplace equation. It is intended mainly for characterization of liquid coating materials; restrictions can apply when testing non‑Newtonian liquids.
Key topics and technical requirements
- Method principle: Form a pendant drop on a cylindrical needle and analyse its axisymmetric contour to derive surface tension from Young–Laplace.
- Apparatus: State‑of‑the‑art drop contour analysis system (camera, optical system, light source), a dosing unit/micro‑syringe and a needle with outside diameter between 0.5 mm and 2.5 mm (needle choice depends on σ/Δρ).
- Sample handling: Representative sampling per ISO 15528; density of liquid and ambient phase measured per the ISO 2811 series.
- Test conditions: Conduct at (23 ± 2) °C and (50 ± 5) % RH; enter local gravity value in instrument software.
- Image quality & evaluation:
- Axially symmetric drop contour mandatory.
- Shape parameter B recommended to be 0.60 ± 0.06 (Annex B).
- Fit error should be
Технические детали
- Технический комитет
- ISO/TC 35/SC 9 - General test methods for paints and varnishes
- SKU
- ISO 19403-3:2024
Похожие стандарты
Упомянутые в описании и другие стандарты ISO
BS EN ISO 15528:2020
ДействующийPaints, varnishes and raw materials for paints and varnishes. Sampling.
SIST EN ISO 2811-3:2024
ДействующийPaints and varnishes - Determination of density - Part 3: Oscillation method (ISO 2811-3:2023)
Overview - EN ISO 2811-3:2023 (Oscillation method for density) EN ISO 2811-3:2023 specifies an oscillation method for determining the density of paints, varnishes and related products. The method use…
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…