ISO 21270:2004 PDF

Name: ISO 21270:2004 — Surface chemical analysis — X-ray photoelectron and Auger electron spectrometers — Linearity of intensity scale
SKU: ISO 21270:2004
Price: 25 EUR
Availability: InStock

Surface chemical analysis — X-ray photoelectron and Auger electron spectrometers — Linearity of intensity scale

Название (английский):

ISO 21270:2004

Surface chemical analysis — X-ray photoelectron and Auger electron spectrometers — Linearity of intensity scale

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 13
Дата публикации:: 15 июня 2004 г.
Издание:: ISO IS 21270 edition 1 version 1
ICS:: 71.040.40

Тип поставки:

Full version195 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:3 раб. дн. (перевод)

Цена:195 €

Описание (английский):

ISO 21270:2004 specifies two methods for determining the maximum count rate for an acceptable limit of divergence from linearity of the intensity scale of Auger and X-ray photoelectron spectrometers. It also includes methods to correct for intensity non-linearities so that a higher maximum count rate can be employed for those spectrometers for which the relevant correction equations have been shown to be valid.

Abstract

Похожие стандарты

Упомянутые в описании и другие стандарты ISO

Overview

ISO 21270:2004 - "Surface chemical analysis - X‑ray photoelectron and Auger electron spectrometers - Linearity of intensity scale" defines procedures to evaluate and, where possible, correct the linearity of the intensity scale for X‑ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) instruments. The standard provides two methods to determine the maximum count rate compatible with an acceptable divergence from linear response, and it describes correction relationships (based on detector dead‑time models) that extend usable count‑rate ranges for instruments where those corrections are valid.

Key topics and requirements

Two measurement methods

Varying source flux method: for AES and XPS instruments that allow 30 or more approximately evenly spaced source flux settings; uses a sputter‑cleaned polycrystalline copper (Cu) sample and measures count rate vs. beam/X‑ray flux.
Spectrum ratio method: for XPS instruments with two or more but fewer than 30 predefined X‑ray source settings; compares widescan spectra at high and low emission currents (Cu or stainless‑steel sample).

Sample preparation

Preferred sample: polycrystalline Cu (≥ 99.8 %); alternative: stainless steel or a sample holder when no ion gun is available.
Cleaning: short 1 % nitric acid dip then rinse (if needed); ion sputter cleaning in ultra‑high vacuum to reduce C and O signals below specified limits; adhesives are prohibited for mounting.

Linearity assessment and correction

Plot ratios (measured count/flux or spectrum‑ratio vs. count rate) to define linear range.
Use dead‑time based correction equations (extended/non‑extended dead time) where valid to correct non‑linearities and allow higher maximum count rates.

When to perform

Characterization of new instruments, after substantive detection‑circuit modifications, after multiplier replacement, after a substantial increase in multiplier voltage, or at ~12‑month intervals.

Documentation

Record spectrometer settings (pass energy, slits, lens settings, etc.) - results apply only to the tested configuration.

Applications and users

Who uses it: surface analysis labs, XPS/AES instrument manufacturers, calibration and quality control engineers, and R&D groups performing quantitative surface chemical analysis.

Practical value: ensures accurate quantitative surface composition by identifying count‑rate limits and applying validated corrections; informs acceptable instrument operating ranges to minimize systematic errors from detector non‑linearity.

Related standards

ISO 18115 (Surface chemical analysis - Vocabulary) is normative for terminology used in ISO 21270.

Relevant to laboratory quality systems, instrument calibration procedures, and ISO standards on surface analysis practices.

Keywords: ISO 21270:2004, XPS linearity, AES intensity scale, detector dead time, spectrum ratio method, maximum count rate, surface chemical analysis, X‑ray photoelectron spectrometer.

ISO 21270:2004 PDF

Abstract

Похожие стандарты

Overview

Key topics and requirements

Applications and users

Related standards

Технические детали

ISO 18115-2:2010

Surface chemical analysis — Vocabulary — Part 2: Terms used in scanning-probe microscopy

ISO 8689-1:2000

Water quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…

ISO/ASTM51540-04(2012)

Standard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)

ISO/ASTM51204-04

Standard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)

ISO/ASTM51431-05

Standard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…

ISO/ASTM52628-20e1

Standard Practice for Dosimetry in Radiation Processing

ISO/ASTM52921-13(2019)

Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies

ISO/ASTMTR52917-EB

Additive Manufacturing — Round Robin Testing — General Guidelines