ISO 21561-1:2015 PDF

Styrene-butadiene rubber (SBR) — Determination of the microstructure of solution-polymerized SBR — Part 1: 1H-NMR and IR with cast-film method

Название (английский):

ISO 21561-1:2015

Styrene-butadiene rubber (SBR) — Determination of the microstructure of solution-polymerized SBR — Part 1: 1H-NMR and IR with cast-film method

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 17
Дата публикации:: 17 июля 2015 г.
Издание:: ISO IS 21561 edition 1 version 1
ICS:: 83.060

Тип поставки:

Full version255 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:3 раб. дн. (перевод)

Цена:255 €

Описание (английский):

ISO 21561-1:2015 specifies procedures for the quantitative determination of the microstructure of the butadiene and the content of styrene in solution-polymerized SBR (S-SBR) by 1H-NMR spectrometry as an absolute method and by IR spectrometry as a relative method. The styrene content is expressed in mass % relative to the whole polymer. The trans, cis and vinyl contents are expressed in mol % relative to the butadiene. These methods are applicable only for raw rubber. NOTE 1 IR spectrometry can also give absolute values of microstructure by calibration with S-SBRs of known absolute microstructure obtained by 1H-NMR spectrometry. NOTE 2 Only "vinyl", "trans" and "cis" are used in this part of ISO 21561. However, the expression of vinyl, trans and cis mean as follows in general: - vinyl: vinyl unit, vinyl bond, 1,2-unit, 1,2-bond, 1,2-vinyl-unit or 1,2-vinyl-bond; - trans: 1,4-trans unit, 1,4-trans bond, trans-1,4 unit or trans1,4 bond; - cis: 1,4-cis unit, 1,4-cis bond, cis-1,4 unit or cis-1,4 bond.

Технические детали

Технический комитет: ISO/TC 45/SC 3 - Raw materials (including latex) for use in the rubber industry
SKU: ISO 21561-1:2015

Abstract

Overview

ISO 21561-1:2015 specifies laboratory procedures for the quantitative determination of the microstructure of solution‑polymerized styrene‑butadiene rubber (S‑SBR). It defines two analytical routes:

1H‑NMR (H‑NMR) as an absolute method for determining styrene content (mass %) and butadiene microstructure (trans, cis, vinyl expressed in mol % relative to butadiene), and
IR spectrometry with the cast‑film method as a relative method, which can be calibrated against H‑NMR standards to give absolute values.

The standard applies only to raw (unvulcanized) S‑SBR and references ISO 1407 (solvent extraction) and ISO 1795 (sampling).

Key topics and technical requirements

Sample preparation
- Extract extender oils and antioxidants per ISO 1407 (ethanol‑toluene azeotrope or acetone); dry extracted rubber under vacuum at 50–60 °C.
H‑NMR (absolute method)
- Dissolve 15–50 mg of extracted S‑SBR in 0.5 ml CDCl3 containing 0.03 % TMS.
- Use an FT‑NMR spectrometer with resonance frequency ≥150 MHz.
- Measurement parameters include 15 ppm sweep width, 30° pulse, pulse repetition 4–30 s, accumulation 32–256 scans.
- Microstructure is obtained by integrating defined spectral regions (areas A, B, C) and applying the standard’s calculation formulas.
IR cast‑film method (relative method)
- Dissolve 0.2 g extracted S‑SBR in 10 ml cyclohexane; cast a film on KBr plate using a 0.1 mm spacer.
- Measure FTIR or double‑beam IR spectrum from 1 200 cm‑1 to 600 cm‑1. Target maximum absorbance 0.10–0.15 for reproducibility.
- Calculate trans/cis/vinyl/styrene using specified peak absorbances (Hampton’s method); calibration against H‑NMR yields absolute values.
Precision and reporting
- The standard includes precision data, procedural notes for film preparation (Annex A), and required test report elements.

Practical applications and users

ISO 21561-1 is used where accurate characterization of S‑SBR microstructure is required:

Rubber manufacturers for batch acceptance and process control.
Quality control and testing laboratories performing routine composition and microstructure checks.
Polymer R&D and formulation scientists studying structure–property relationships (e.g., glass transition, filler interactions).
Raw material suppliers verifying styrene content and butadiene stereochemistry.
Certification and compliance bodies requiring standardized test data.

Keywords: ISO 21561-1, styrene‑butadiene rubber, SBR microstructure determination, 1H‑NMR, IR spectrometry, cast‑film method, FTIR, raw S‑SBR.

Related standards

ISO 21561‑2 - SBR microstructure: FTIR with ATR method (complements Part 1).
ISO 1407 - Rubber: determination of solvent extract (sample extraction).
ISO 1795 - Rubber sampling and preparative procedures.

Overview

1H‑NMR (H‑NMR) as an absolute method for determining styrene content (mass %) and butadiene microstructure (trans, cis, vinyl expressed in mol % relative to butadiene), and
IR spectrometry with the cast‑film method as a relative method, which can be calibrated against H‑NMR standards to give absolute values.

The standard applies only to raw (unvulcanized) S‑SBR and references ISO 1407 (solvent extraction) and ISO 1795 (sampling).

Key topics and technical requirements

Sample preparation
- Extract extender oils and antioxidants per ISO 1407 (ethanol‑toluene azeotrope or acetone); dry extracted rubber under vacuum at 50–60 °C.
H‑NMR (absolute method)
- Dissolve 15–50 mg of extracted S‑SBR in 0.5 ml CDCl3 containing 0.03 % TMS.
- Use an FT‑NMR spectrometer with resonance frequency ≥150 MHz.
- Measurement parameters include 15 ppm sweep width, 30° pulse, pulse repetition 4–30 s, accumulation 32–256 scans.
- Microstructure is obtained by integrating defined spectral regions (areas A, B, C) and applying the standard’s calculation formulas.
IR cast‑film method (relative method)
- Dissolve 0.2 g extracted S‑SBR in 10 ml cyclohexane; cast a film on KBr plate using a 0.1 mm spacer.
- Measure FTIR or double‑beam IR spectrum from 1 200 cm‑1 to 600 cm‑1. Target maximum absorbance 0.10–0.15 for reproducibility.
- Calculate trans/cis/vinyl/styrene using specified peak absorbances (Hampton’s method); calibration against H‑NMR yields absolute values.
Precision and reporting
- The standard includes precision data, procedural notes for film preparation (Annex A), and required test report elements.

Practical applications and users

ISO 21561-1 is used where accurate characterization of S‑SBR microstructure is required:

Rubber manufacturers for batch acceptance and process control.
Quality control and testing laboratories performing routine composition and microstructure checks.
Polymer R&D and formulation scientists studying structure–property relationships (e.g., glass transition, filler interactions).
Raw material suppliers verifying styrene content and butadiene stereochemistry.
Certification and compliance bodies requiring standardized test data.

Keywords: ISO 21561-1, styrene‑butadiene rubber, SBR microstructure determination, 1H‑NMR, IR spectrometry, cast‑film method, FTIR, raw S‑SBR.

Related standards

ISO 21561‑2 - SBR microstructure: FTIR with ATR method (complements Part 1).
ISO 1407 - Rubber: determination of solvent extract (sample extraction).
ISO 1795 - Rubber sampling and preparative procedures.

ISO 21561-1:2015 PDF

Технические детали

Abstract

Overview

Key topics and technical requirements

Practical applications and users

Related standards

Похожие стандарты

Abstract

Overview

Key topics and technical requirements

Practical applications and users

Related standards

Похожие стандарты

Rubber. Determination of solvent extract.

Rubber, raw natural and raw synthetic — Sampling and further preparative procedures

Styrene-butadiene rubber (SBR) — Determination of the microstructure of solution-polymerized SBR — Amendment 1