ISO 2286-1:2016 PDF
Rubber- or plastics-coated fabrics — Determination of roll characteristics — Part 1: Methods for determination of length, width and net mass
Rubber- or plastics-coated fabrics — Determination of roll characteristics — Part 1: Methods for determination of length, width and net mass
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 3
- Дата публикации:
- 15 сентября 2016 г.
- Издание:
- ISO IS 2286 edition 2 version 1
- ICS:
- 59.080.40
ISO 2286-1:2016 specifies methods of determining the length, width and net mass of a roll of rubber- or plastics-coated fabrics.
Abstract
Overview
ISO 2286-1:2016 specifies standardized methods for determining the length, usable width and net mass of a roll of rubber‑ or plastics‑coated fabrics. It defines the required apparatus, measurement procedures and reporting elements used for consistent roll characterization in production, inspection and contractual verification.
Key topics and technical requirements
- Scope: Measurement procedures apply to rolls of rubber‑ or plastics‑coated fabrics and form Part 1 of the ISO 2286 series.
- Apparatus:
- Measuring surface: flat, horizontal, ≥ 5 m long and at least as wide as the roll; longitudinal edges marked in 1 m lengths with at least one section marked at 1 cm intervals.
- Measuring scale: longer than fabric width, graduated in millimetres.
- Balance: accurate to the nearest 100 g.
- Length determination:
- Trim roll ends to be perpendicular to the roll axis (minimum trimming).
- Unroll without introducing tension, mark edges at fixed divisions, and measure sequential lengths along the measuring surface.
- Final length measured to the nearest 100 mm, unless otherwise agreed. The method is the referee method in disputes.
- Alternative mechanical, electromechanical or photoelectric measuring equipment may be used but can be unsuitable for extensible substrates (e.g., knitted).
- Usable width:
- Measure while unrolled and free of tension at 10 m intervals using the measuring scale.
- Record to the nearest 5 mm; for rolls
Технические детали
- Технический комитет
- ISO/TC 45/SC 4 - Products (other than hoses)
- SKU
- ISO 2286-1:2016
Похожие стандарты
Упомянутые в описании и другие стандарты ISO
BS ISO 22863-4:2021
ДействующийFireworks. Test methods for determination of specific chemical substances. Analysis of lead and lead compound…
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…