ISO 22863-12:2022 PDF
Fireworks — Test methods for determination of specific chemical substances — Part 12: Picrates and picric acid by high performance liquid chromatography
Fireworks — Test methods for determination of specific chemical substances — Part 12: Picrates and picric acid by high performance liquid chromatography
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 6
- Дата публикации:
- 13 сентября 2022 г.
- Издание:
- ISO IS 22863 edition 1 version 1
- ICS:
- 71.100.30
This document specifies the test method for the determination of picrates and picric acid in firework compositions by high performance liquid chromatography.
Abstract
Overview
ISO 22863-12:2022 specifies a validated test method for the determination of picrates and picric acid in fireworks and pyrotechnic compositions using high performance liquid chromatography (HPLC). The standard describes sample preparation, extraction, chromatographic conditions, qualitative identification by retention time, and quantitative determination with an external standard calibration curve. It is part of the ISO 22863 series developed by ISO/TC 264 (Fireworks).
Key topics and requirements
- Scope: Determination of picric acid and picrates in firework compositions by HPLC.
- Principle: Hot-water extraction of picrate anions followed by HPLC under acidic conditions; detection by UV (350 nm) and comparison to external picric acid standards.
- Sample preparation:
- Sample mass: 0.5 g
- Extraction: 5 ml hot deionized water, ultrasonic mixing 40 min, centrifuge 2 min at 3 000 r/min; repeat three times and combine to 25 ml.
- Filtration through 0.45 µm organic Millipore device.
- HPLC settings (specified):
- Column: C18 (4.6 × 250 mm, 5 µm) or equivalent
- Mobile phase: Methanol : 0.1% glacial acetic acid = 55:45 (v/v)
- Flow rate: 0.8 ml/min, injection volume 10 µl
- Detection wavelength: 350 nm
- Calibration and quantification:
- External standard (picric acid, ≥99% purity) reserve solution (100 µg/ml), prepare diluted standards to build a linear response curve.
- Calculate sample concentration from peak area and standard curve; blank and parallel tests required.
- Performance:
- Reported recovery: ~89.4%–96.4% in the 0.5–20 mg/kg range
- Relative standard deviation (RSD)
Технические детали
- Технический комитет
- ISO/TC 264 - Fireworks
- SKU
- ISO 22863-12:2022
Похожие стандарты
Упомянутые в описании и другие стандарты ISO
BS ISO 22863-4:2021
ДействующийFireworks. Test methods for determination of specific chemical substances. Analysis of lead and lead compound…
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…