ISO 23230:2023 PDF
Space systems — Paints and varnishes — Processes, procedures, and requirements for coating materials and coatings
Space systems — Paints and varnishes — Processes, procedures, and requirements for coating materials and coatings
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 17
- Дата публикации:
- 13 января 2023 г.
- Издание:
- ISO IS 23230 edition 1 version 1
- ICS:
- 49.140
This document establishes the main requirements for: — a choice of coating materials and coatings for space applications; — processes and procedures for the verification of coating materials; — processes of preparation and quality control of the painted surface; — the quality control of the applied coatings. This document also describes the causes of possible defects in coatings. This document is applicable to coating materials and coatings based on them; it is intended for use by manufacturers of space systems products for various surfaces of spacecraft’s and its constitutive parts (on-board systems, facilities, tools, electronic component base products) with long active lifetimes.
Abstract
Overview
ISO 23230:2023 - "Space systems - Paints and varnishes - Processes, procedures, and requirements for coating materials and coatings" defines requirements and best practices for selecting, verifying, preparing, applying and inspecting paints, varnishes and other coating materials used on spacecraft and space-system components. The standard targets coatings with long active lifetimes and harmonizes international requirements to improve coating quality and reliability in the space environment.
Key topics and technical requirements
-
Scope and purpose
- Selection of coating materials and coatings for space applications.
- Processes and procedures for verification, surface preparation, application, curing and quality control.
- Identification of coating defect types and their causes.
-
Required coating properties
- Thermal control, electrically conductive or insulating, thermal resistance, anticorrosion, chemical resistance and resistance to space environment factors.
-
Verification and testing
- Material verification and validation procedures (referenced to ISO 10794 and ECSS‑Q‑ST‑70‑71C).
- Environmental testing: accelerated aging, salt spray (ISO 9227), thermal cycling, atomic oxygen, particle and UV exposure.
- Outgassing metrics: TML (total mass loss), RML (recovered mass loss) and CVCM (collected volatile condensable materials). Materials with TML
Технические детали
- Технический комитет
- ISO/TC 20/SC 14 - Space systems and operations
- SKU
- ISO 23230:2023
Похожие стандарты
Упомянутые в описании и другие стандарты ISO
ISO 10794:2011
ОтменёнSpace systems — Programme management — Material, mechanical parts and processes
SIST EN ISO 9227:2023/A1:2024
ДействующийCorrosion tests in artificial atmospheres - Salt spray tests - Amendment 1: Footnote of warning (ISO 9227:202…
Overview SIST EN ISO 9227:2023/A1:2024 is an important amendment to the widely recognized standard for corrosion tests in artificial atmospheres: salt spray tests. Published by the European Committee…
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…