ISO 23274:2007 PDF
Hybrid-electric road vehicles — Exhaust emissions and fuel consumption measurements — Non-externally chargeable vehicles
Hybrid-electric road vehicles — Exhaust emissions and fuel consumption measurements — Non-externally chargeable vehicles
- Статус документа:
- Отменён
- Формат:
- Электронный (PDF)
- Количество страниц:
- 38
- Дата публикации:
- 6 июня 2007 г.
- Издание:
- ISO IS 23274 edition 1 version 1
- ICS:
- 43.120
ISO 23274:2007 establishes a uniform chassis dynamometer test procedure for hybrid-electric road vehicles (HEV) with internal combustion engines (ICE) classified as passenger cars and light duty trucks, as defined in each regional annex. ISO 23274:2007 proposes ways of correcting the measured emissions and fuel consumption of HEV, in order to obtain the correct values when the battery state of charge (SOC) of the rechargeable energy storage system (RESS) does not remain the same between the beginning and the end of test cycle. ISO 23274:2007 applies to HEV with ICE of which the nominal energy of the RESS is at least 2 % of the total energy consumption by the vehicle over the test cycle. ISO 23274:2007 applies to non-externally chargeable vehicles without an operating mode switch to draw propulsion energy from the following sources of energy: consumable fuel, and an energy storage battery/capacitor system that is rechargeable only by an on-board engine-generator/electric motor system. Consumable fuels covered by ISO 23274:2007 are limited to petroleum-based liquid fuels (e.g. gasoline and diesel fuel).
Технические детали
- Технический комитет
- ISO/TC 22 - Road vehicles
- SKU
- ISO 23274:2007
Похожие стандарты
Другие стандарты ISO
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…
ISO/ASTM52901-17(2023)
ДействующийStandard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts
Scope 1.1 This document defines and specifies requirements for purchased parts made by additive manufacturing. 1.2 It gives guidelines for the elements to be exchanged between the customer and the pa…