ISO 3013:1997 PDF
Petroleum products — Determination of the freezing point of aviation fuels
Petroleum products — Determination of the freezing point of aviation fuels
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 8
- Дата публикации:
- 4 сентября 1997 г.
- Издание:
- ISO IS 3013 edition 2 version 1
- ICS:
- 75.160.20
La présente Norme internationale prescrit une méthode de détermination de la température en dessous de laquelle se trouvent des cristaux d'hydrocarbures dans les carburéacteurs ou les essences aviation.
Abstract
Overview
ISO 3013:1997 specifies a laboratory method for determining the freezing point of aviation fuels - the temperature at which solid hydrocarbon crystals disappear on warming. This second edition (1997) covers aviation turbine fuels and aviation gasolines and defines apparatus, reagents, test procedure, thermometer requirements (Annex A), precision limits and reporting. The method is widely used for fuel certification, quality control and cold-weather performance assessment.
Key Topics and Requirements
- Scope: Determination of the temperature below which solid hydrocarbon crystals are present (freezing point) and the temperature at which crystals first appear (crystallization point).
- Sample: Transfer 25 ml ± 1 ml into a clean, dry jacketed sample tube; position thermometer bulb 10–15 mm above tube center.
- Apparatus:
- Jacketed sample tube (double-walled, unsilvered) in an unsilvered vacuum flask.
- Stirrer: brass or stainless rod, 1.6 mm diameter, with three-loop spiral; stirring rate 1–1.5 cycles/s.
- Moisture‑proof collar (type A or B) to prevent moisture ingress.
- Thermometer conforming to Annex A (range -80 °C to +20 °C, 0.5 °C graduations, specified stem/bulb dimensions and calibration).
- Coolants: preferred liquid propan-2-ol combined with solid carbon dioxide (dry ice) or liquid nitrogen where required. Other acceptable liquids: ethanol, acetone, methanol. Liquid nitrogen permitted only for aviation gasolines or when freezing point
Технические детали
- Технический комитет
- ISO/TC 28 - Petroleum and related products, fuels and lubricants from natural or synthetic sources
- SKU
- ISO 3013:1997
Похожие стандарты
Другие стандарты ISO
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…
ISO/ASTM52901-17(2023)
ДействующийStandard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts
Scope 1.1 This document defines and specifies requirements for purchased parts made by additive manufacturing. 1.2 It gives guidelines for the elements to be exchanged between the customer and the pa…