ISO 4116:1986 PDF

Name: ISO 4116:1986 — Air cargo equipment — Ground equipment requirements for compatibility with aircraft unit load devices
SKU: ISO 4116:1986
Price: 25 EUR
Availability: InStock

Air cargo equipment — Ground equipment requirements for compatibility with aircraft unit load devices

Название (английский):

ISO 4116:1986

Air cargo equipment — Ground equipment requirements for compatibility with aircraft unit load devices

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 4
Дата публикации:: 17 июля 1986 г.
Издание:: ISO IS 4116 edition 2 version 1
ICS:: 49.100

Тип поставки:

Full version60 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:1 раб. дн. (перевод)

Цена:60 €

Описание (английский):

Specifies requirements for those portions of ground and terminal handling equipment that will have a direct bearing on the life of the device for the purpose of preventing on due wear on the device. Covers requirements for conveyor systems, guides, stops and restraint hardware that are used on trucks, transporters, dollies, storage provisions, pallet build-up hoists, or other device-handling equipment. The devices can be containers, galley modules and pallets for aircraft galley and cargo systems.

Abstract

Похожие стандарты

Упомянутые в описании и другие стандарты ISO

Overview

ISO 4116:1986 defines requirements for ground and terminal handling equipment that directly affect the service life of aircraft unit load devices (ULDs). Its purpose is to prevent undue wear and damage to containers, pallets and galley modules by establishing design and operational criteria for conveyors, guides, stops and restraint hardware used on trucks, transporters, dollies, storage provisions and pallet build-up hoists.

This International Standard was prepared by ISO/TC 20 (Aircraft and space vehicles) and is intended to be applied to equipment manufactured or installed after its publication. It complements device manufacturer guidance, airline operator practices and applicable IATA specifications.

Key Topics

Conveyor systems (uni-directional and multi-directional)

Minimum roller diameter: 50 mm (2 in) and minimum effective bearing length: 100 mm (4 in).
Cumulative roller length on a common axis shall support at least 50% of the corresponding device dimension; staggered roller patterns are acceptable.
Ball-transfer and castored-roller spacing and diameter requirements are specified to limit point loads and reduce wear (examples in the standard: ball diameter min 25 mm (1 in); ball pre-load suggested close to 310 N (70 lbf), not less than 150 N and not exceeding 450 N).
Allowable height differences for rollers and unloaded ball transfers: maximum 3.2 mm in any 1.52 m x 1.52 m area, and 1.3 mm between adjacent units.

Flat-top systems and contact requirements

Flat conveying or storage surfaces must provide a minimum percentage of contact area (20% for transient traversing conditions) and limit overhangs to specified maxima.

Stops, guides and restraints

Guide rails and end stops typically extend at least 101.6 mm above the conveying surface; centre-to-centre distance for stops shall not exceed 635 mm and minimum width is 50.8 mm.
Systems must provide fore, aft, lateral and vertical restraint; energy-absorbing stops are required where impact velocities exceed defined thresholds.

Operational procedures

Transport speed categories and rules for door latching, net securing, stacking limitations and pre-movement restraint application are covered to reduce damage and risk during handling.

Applications

Ground equipment manufacturers: design validation and specification of conveyors, dollies and pallet-handling devices.

Airport and airline cargo operations: selection and maintenance of handling systems to extend ULD life and reduce lifecycle costs.

Maintenance and safety teams: verifying restraint, stop and guide performance to improve personnel safety and prevent cargo damage.

Related Standards

ISO 4116 references device manufacturer requirements, airline operator practices and IATA specifications for detailed sizing and installation matters.

Prepared by ISO/TC 20 (Aircraft and space vehicles); users should consult the latest editions of referenced International Standards and industry guidance when applying ISO 4116:1986.

For design, procurement or audit activities, consult the full ISO 4116:1986 document and coordinate with ULD manufacturers and airline operations to ensure compatibility and compliance.

ISO 4116:1986 PDF

Abstract

Похожие стандарты

Overview

Key Topics

Applications

Related Standards

Технические детали

ISO 4116:1980

Ground equipment requirements for compatibility with aircraft unit load devices

ISO 8689-1:2000

Water quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…

ISO/ASTM51540-04(2012)

Standard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)

ISO/ASTM51204-04

Standard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)

ISO/ASTM51431-05

Standard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…

ISO/ASTM52628-20e1

Standard Practice for Dosimetry in Radiation Processing

ISO/ASTM52921-13(2019)

Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies

ISO/ASTMTR52917-EB

Additive Manufacturing — Round Robin Testing — General Guidelines