ISO 6336-6:2019 PDF

Name: ISO 6336-6:2019 — Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load
SKU: ISO 6336-6:2019
Price: 25 EUR
Availability: InStock

Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load

Название (английский):

ISO 6336-6:2019

Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 42
Дата публикации:: 26 ноября 2019 г.
Издание:: ISO IS 6336 edition 2 version 1
ICS:: 21.200

Тип поставки:

Full version630 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:7 раб. дн. (перевод)

Цена:630 €

Описание (английский):

This document specifies the information and standardized conditions necessary for the calculation of the service life (or safety factors for a required life) of gears subject to variable loading for only pitting and tooth root bending strength. If this scope does not apply, refer ISO 6336-1:2019, Clause 4.

Abstract

Похожие стандарты

Стандарты, упомянутые в описании

ISO 6336-6:2019 - Overview

ISO 6336-6:2019 is Part 6 of the ISO 6336 series and specifies the standardized information and conditions required to calculate service life (or safety factors for a required life) of spur and helical gears under variable loading, limited to the two failure modes: pitting (surface fatigue) and tooth root bending strength (tooth breakage). This second edition (2019) updates the earlier 2006 edition and integrates Annex B on equivalent cumulative damage.

Key topics and technical requirements

Scope limitation: Applies only to pitting and tooth-root bending strength under variable loads. If other failure modes or conditions apply, refer to ISO 6336-1:2019.

Terminology and symbols: Uses terms, symbols and abbreviations defined in ISO 6336-1 and ISO 1122-1.

Load and stress spectra determination: Variable loading can be derived by:

experimental measurement of operating loads,
estimation from similar machines and operating modes,
calculation via known excitations and mass-elastic system simulation (preferably validated experimentally).

General calculation of service life: Methods for converting load spectra into fatigue damage and service life estimates are provided.

Fatigue accumulation rule: Incorporates the Palmgren–Miner linear damage rule for cumulative damage assessment.

Service strength based on single-stage strength: Procedures to derive service strength from ISO 6336 single-stage calculations, including:

calculation of stress spectra,
determination of pitting and bending strength values,
determination of safety factors for required life.

Annexes:

Annex A (normative): Determination of the application factor K from a given load spectrum using an equivalent torque concept.
Annex B (informative): Equivalent cumulative damage - methods for converting complex spectra to equivalent damage cycles.
Annex C (informative): Example calculation for safety factor from a given load spectrum.

Practical applications and users

ISO 6336-6:2019 is intended for engineers and organizations involved in:

gearbox and gear set design and verification,

mechanical and reliability engineering for rotating equipment,

drivetrain component manufacturers and testing laboratories,

maintenance planners assessing remaining life under variable duty cycles,

purchasers and specifiers requiring standardized life and safety-factor calculations.

Typical uses include predicting pitting and bending fatigue life under realistic, variable operating loads, deriving safety factors for design acceptance, and converting measured or simulated load spectra into standardized life estimates.

Related standards

ISO 6336-1:2019 - Basic principles and general influence factors

ISO 6336-2 - Calculation of surface durability (pitting)

ISO 6336-3 - Calculation of tooth bending strength

ISO 1122-1:1998 - Vocabulary of gear terms

Keywords: ISO 6336-6:2019, gear service life, variable load, pitting, tooth root bending, gear fatigue, load spectra, Palmgren–Miner, equivalent torque, application factor.

ISO 6336-6:2019 PDF

Abstract

Похожие стандарты

ISO 6336-6:2019 - Overview

Key topics and technical requirements

Practical applications and users

Related standards

Технические детали

ISO 6336-1:2019

Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general i…

ISO 1122-1:1998

Vocabulary of gear terms — Part 1: Definitions related to geometry

SIST ISO 6336-1:2020

Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general i…

BS ISO 11221:2011

Space systems. Space solar panels. Spacecraft charging induced electrostatic discharge test methods.

SIST ISO 6336-2:2020

Calculation of load capacity of spur and helical gears - Part 2: Calculation of surface durability (pitting)

SIST ISO 6336-3:2020

Calculation of load capacity of spur and helical gears - Part 3: Calculation of tooth bending strength