ISO 6703-2:1984 PDF
Water quality — Determination of cyanide — Part 2: Determination of easily liberatable cyanide
Water quality — Determination of cyanide — Part 2: Determination of easily liberatable cyanide
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 11
- Дата публикации:
- 1 августа 1984 г.
- Издание:
- ISO IS 6703 edition 1 version 1
- ICS:
- 13.060.50
The three methods specified are applicable to water containing less than 50 mg per litre and less than 100 mg of total cyanide per litre, but higher concentrations may be determined by suitable dilution of the sample. The methods suitable and corresponding ranges are as follows: photometric method with pyridine/barbituric acid: 0,002 to 0,025 mg; titrimetric method using the tyndall effect: > 0,005 mg; titrimetric method using an indicator: > 0,05 mg. Ions and compounds interfering with the determination are listed in table 1.
Abstract
Overview - ISO 6703-2:1984 (Water quality - Easily liberatable cyanide)
ISO 6703-2:1984 specifies procedures for the determination of easily liberatable cyanide in water. The part covers liberation of hydrogen cyanide (HCN) from a sample by acidification and metal-assisted reduction, entrainment by a carrier gas, and absorption into alkaline solution, followed by one of three quantitative analytical methods. It is applicable to natural waters, municipal sewage and industrial effluents and is intended for routine monitoring and process control in water and wastewater treatment.
Key topics and technical requirements
- Scope and limits
- Applicable to samples with
Технические детали
- Технический комитет
- ISO/TC 147/SC 2 - Physical, chemical and biochemical methods
- SKU
- ISO 6703-2:1984
Похожие стандарты
Другие стандарты ISO
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…
ISO/ASTM52901-17(2023)
ДействующийStandard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts
Scope 1.1 This document defines and specifies requirements for purchased parts made by additive manufacturing. 1.2 It gives guidelines for the elements to be exchanged between the customer and the pa…