ISO 7176-19:2022 PDF
Wheelchairs — Part 19: Wheelchairs for use as seats in motor vehicles
Wheelchairs — Part 19: Wheelchairs for use as seats in motor vehicles
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 91
- Дата публикации:
- 5 апреля 2022 г.
- Издание:
- ISO IS 7176 edition 3 version 1
- ICS:
- 11.180.10
This document specifies test methods, requirements and recommendations for wheelchairs intended for use as seats in motor vehicles related to design, performance, labelling, presale literature, user instructions and user warnings. This document is applicable to all manual and powered wheelchairs, including scooters, which, in addition to their primary function as wheeled mobility devices, are also likely to be used as forward-facing seats in motor vehicles by children and adults with a body mass equal to or greater than 12 kg. This document is applicable to complete wheelchairs, including a frame or powerbase and seating system. It is also applicable to wheelchairs equipped with additional components designed to facilitate conformity with one or more of the requirements of this document.
Abstract
Overview
ISO 7176-19:2022 - Wheelchairs for use as seats in motor vehicles specifies test methods, design and performance requirements, labelling, presale literature and user information for wheelchairs intended to be used as forward‑facing seats in motor vehicles. It applies to complete manual and powered wheelchairs (including scooters) and seating systems for occupants with a body mass of ≥ 12 kg, covering components that assist conformity to the standard. The standard aims to improve crashworthiness, occupant restraint compatibility and real‑world securement of wheelchair‑seated passengers.
Key topics and technical requirements
- Design requirements and recommendations
- Wheelchair securement points and accessibility for tiedowns
- Accommodation of vehicle‑mounted three‑point belts and wheelchair‑mounted restraints
- Head and back support requirements for small children and risk management for modifications
- Performance requirements
- Dynamic frontal impact testing procedures (Annex A) - evaluated with an instrumented crash dummy and a 48 km/h crash pulse
- Requirements for tiedown clear‑paths, accessibility and securement strength
- Provisions for wheelchair‑mounted occupant restraints and five‑point harnesses for children (
Технические детали
- Технический комитет
- ISO/TC 173/SC 1 - Wheelchairs
- SKU
- ISO 7176-19:2022
Похожие стандарты
Другие стандарты ISO
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…
ISO/ASTM52901-17(2023)
ДействующийStandard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts
Scope 1.1 This document defines and specifies requirements for purchased parts made by additive manufacturing. 1.2 It gives guidelines for the elements to be exchanged between the customer and the pa…