ISO 9043:2008 PDF
Mopeds — Measurement method for moments of inertia
Mopeds — Measurement method for moments of inertia
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 17
- Дата публикации:
- 21 февраля 2008 г.
- Издание:
- ISO IS 9043 edition 2 version 1
- ICS:
- 43.140
ISO 9043:2008 specifies a measuring method for determining the moments of inertia of the moped and of the moped/rider combination. It applies to two-wheeled mopeds. Other measuring methods can be used if it is demonstrated that the results are equivalent. Measurement results obtained exclusively by the method described in ISO 9043:2008 cannot be used for an evaluation of vehicle stability because they deal with only one aspect of this very complex phenomenon.
Abstract
Overview
ISO 9043:2008 - "Mopeds - Measurement method for moments of inertia" defines a standardized laboratory method to determine the moments of inertia of two-wheeled mopeds and moped/rider combinations. The standard describes measurement conditions, required instruments, and step-by-step procedures to obtain roll, pitch and yaw moments of inertia using pendulum methods. It is intended for engineers, test laboratories and manufacturers who need repeatable inertia data for dynamic modelling, design and validation. Note: results from ISO 9043:2008 alone do not constitute a full vehicle-stability evaluation.
Key topics and technical requirements
- Scope and limitations
- Applies to two-wheeled mopeds and moped/rider combinations.
- Other methods are acceptable if equivalence can be demonstrated.
- Measurement output addresses only one aspect of vehicle stability.
- Measurement conditions
- Moped prepared per manual (fuel, lubricants, tyre pressure), clean and undamaged.
- Suspension fixed; front wheel aligned with the longitudinal axis.
- Rider simulated by a 73.4 kg test dummy (49 CFR Part 572 Subpart B) or equivalent human per protocol.
- Instruments and accuracy
- Precision square level, steel tape, weighing stands (0.1 kg accuracy), stopwatch (0.01 s), rigid lightweight platform, knife edges and balancing weights.
- Measurement procedures
- Centre of gravity located according to ISO 8705 before inertia tests.
- Roll and pitch moments: measured by the physical-pendulum (platform + moped) method - small-angle oscillations recorded and converted to inertia values from oscillation period and geometry.
- Yaw moment: measured by the bifilar-pendulum principle.
- Multiple runs recommended (e.g., averaging repeated 50-cycle timings) and strict alignment/angle limits (oscillation
Технические детали
- Технический комитет
- ISO/TC 22/SC 38 - Motorcycles and mopeds
- SKU
- ISO 9043:2008
Похожие стандарты
Упомянутые в описании и другие стандарты ISO
ISO 8705:1991
ОтменёнMopeds — Measurement method for location of centre of gravity
ISO 8689-1:2000
ДействующийWater quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…
Overview ISO 8689-1:2000, titled Water quality - Biological classification of rivers - Part 1: Guidance on the interpretation of biological quality data from surveys of benthic macroinvertebrates, is…
ISO/ASTM51540-04(2012)
ОтменёнStandard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)
Significance and Use4.1 The radiochromic liquid dosimetry system provides a means of measuring absorbed dose in materials (5-7). Under the influence of ionizing radiation, chemical reactions take pla…
ISO/ASTM51204-04
ДействующийStandard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)
Significance and Use4.1 Food products may be treated with ionizing radiation, such as gamma-rays from 60Co or 137Cs sources, for numerous purposes, including control of parasites and pathogenic micro…
ISO/ASTM51431-05
ОтменёнStandard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…
Significance and Use4.1 Food products may be treated with acceleratorgenerated radiation (electrons and X-rays) for numerous purposes, including control of parasites and pathogenic microorganisms, in…
ISO/ASTM52628-20e1
ДействующийStandard Practice for Dosimetry in Radiation Processing
1.1 This practice describes the basic requirements that apply when making absorbed dose measurements in accordance with the ASTM E61 series of dosimetry standards. In addition, it provides guidance o…
ISO/ASTM52921-13(2019)
ДействующийStandard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
Significance and Use 3.1 Although many additive manufacturing systems are based heavily upon the principles of Computer Numerical Control (CNC), the coordinate systems and nomenclature specific to CN…
ISO/ASTMTR52917-EB
ДействующийAdditive Manufacturing — Round Robin Testing — General Guidelines
This document outlines the steps with regard to aspects of design to conduct and run a round robin study (RRS) to assess the degree of variability in an additive manufacturing material or process. Th…