SIST EN ISO 80601-2-80:2024 PDF
Medical electrical equipment - Part 2-80: Particular requirements for basic safety and essential performance of ventilatory support equipment for ventilatory insufficiency (ISO 80601-2-80:2024)
Medical electrical equipment - Part 2-80: Particular requirements for basic safety and essential performance of ventilatory support equipment for ventilatory insufficiency (ISO 80601-2-80:2024)
- Статус документа:
- Действующий
- Формат:
- Электронный (PDF)
- Количество страниц:
- 131
- Дата публикации:
- 16 сентября 2024 г.
- Издание:
- ISO 80601-2-80:2024
- ICS:
- 11.040.10
NOTE 1 There is guidance or rationale for this subclause contained in Clause AA.2. This document applies to the basic safety and essential performance of ventilatory support equipment, as defined in 201.3.302, for ventilatory insufficiency, as defined in 201.3.302, hereafter also referred to as ME equipment, in combination with its accessories: — intended for use in the home healthcare environment; NOTE 2 In the home healthcare environment, the supply mains driving the ventilatory support equipment is often not reliable. NOTE 3 Such ventilatory support equipment can also be used in professional health care facilities. — intended for use by a lay operator; — intended for use with patients who have ventilatory insufficiency or failure, the most fragile of which would likely experience injury with the loss of this artificial ventilation; — intended for transit-operable use; and — not intended for patients who are dependent on artificial ventilation for their immediate life support. EXAMPLE 1 Patients with moderate to severe chronic obstructive pulmonary disease (COPD), moderate amyotrophic lateral sclerosis (ALS), severe bronchopulmonary dysplasia or muscular dystrophy. Ventilatory support equipment is not considered to use a physiologic closed-loop control system unless it uses a physiological patient variable to adjust the artificial ventilation therapy settings. This document is also applicable to those accessories intended by their manufacturer to be connected to the ventilator breathing system of ventilatory support equipment for ventilatory insufficiency, where the characteristics of those accessories can affect the basic safety or essential performance of the ventilatory support equipment for ventilatory insufficiency. EXAMPLE 2 Breathing sets, connectors, water traps, expiratory valve, humidifier, breathing system filter, external electrical power source, distributed alarm system. If a clause or subclause is specifically intended to be applicable to ME equipment only, or to ME systems only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause applies both to ME equipment and to ME systems, as relevant. Hazards inherent in the intended physiological function of ME equipment or ME systems within the scope of this document are not covered by specific requirements in this document except in IEC 60601‑1:2005+AMD1:2012+AMD2:2020, 7.2.13 and 8.4.1. NOTE 4 Additional information can be found in IEC 60601‑1:2005+AMD1:2012+AMD2:2020, 4.2. NOTE 5 See ISO/TR 21954 for guidance on the selection of the appropriate ventilator for a given patient. This document does not specify the requirements for: — ventilators or accessories for ventilator-dependent patients intended for critical care applications, which are given in ISO 80601‑2‑12; — ventilators or accessories intended for anaesthetic applications, which are given in ISO 80601‑2‑13; — ventilators or accessories intended for the emergency medical services environment, which are given in ISO 80601‑2‑84; — ventilators or accessories intended for ventilator-dependent patients in the home healthcare environment, which are given in ISO 80601‑2‑72; — ventilatory support equipment or accessories intended for ventilatory impairment, which are given in ISO 80601‑2‑79; — sleep apnoea therapy ME equipment, which are given in ISO 80601‑2‑70; — high-frequency jet ventilato
Abstract
Overview
SIST EN ISO 80601-2-80:2024 (identical to ISO 80601-2-80:2024) defines particular requirements for the basic safety and essential performance of ventilatory support equipment intended for patients with ventilatory insufficiency in the home healthcare environment. It covers medical electrical (ME) equipment and relevant accessories intended for lay operation, transit-operable use, and situations where mains power may be unreliable. The standard explicitly excludes ventilators for critical care, anaesthesia, EMS, ventilator-dependent home patients, sleep apnoea therapy and other specialized ventilator classes covered by other ISO parts.
Key topics and technical requirements
- Scope & definitions: Clear definition of ventilatory support equipment, ventilatory insufficiency, and related terms.
- General safety & testing: Requirements for construction, classification, documentation, identification and testing of ME equipment.
- Electrical, mechanical and thermal protection: Protection against electrical hazards, mechanical risks, excessive temperatures and radiation.
- Accuracy & hazardous outputs: Performance limits for controls, instruments and pressure/flow outputs; clarified maximum limited pressure and high airway pressure alarm conditions.
- Alarm systems & usability: Requirements and tests for alarm design, audibility/visibility and usability for lay operators in home settings.
- Power & recovery: Requirements for operation during unreliable mains supply, indication of duration of operation, spontaneous breathing behavior on power loss and system recovery.
- Accessories & interfaces: Applicability to accessories (breathing sets, connectors, water traps, valves, humidifiers, filters, external power sources, distributed alarm systems) whose characteristics affect safety/performance.
- Programmable systems & EMC: Guidance for Programmable Electrical Medical Systems (PEMS), electromagnetic compatibility and disturbance testing.
- Documentation & labeling: Marking, symbols, data interface, and harmonization with ISO 20417 for medical device information.
Practical applications
- Designing and manufacturing home ventilators and portable ventilatory support systems for conditions such as moderate–severe COPD, ALS, bronchopulmonary dysplasia and muscular dystrophy.
- Developing and verifying accessories (tubing, humidifiers, filters, external power packs) that connect to ventilator breathing systems.
- Performing type testing, risk assessment and regulatory compliance activities for CE marking or national conformity as this is a CEN-endorsed European Standard.
- Implementing usability and alarm strategies suitable for lay caregivers and ensuring safe operation during transit or mains interruptions.
Who should use this standard
- Medical device manufacturers, design engineers and test laboratories
- Regulatory affairs and compliance teams
- Clinical/biomedical engineers and procurement specialists
- Certification bodies and standards committees
Related standards
- IEC/ISO general medical electrical safety standards (IEC 60601‑1 series)
- ISO 20417 (medical device labeling information)
- ISO/TR 21954 (ventilator selection guidance)
- Other parts of ISO 80601 (e.g., ISO 80601‑2‑12, ‑2‑13, ‑2‑72, ‑2‑79, ‑2‑70, ‑2‑84) for specialized ventilator types
Keywords: ISO 80601-2-80:2024, ventilatory support equipment, ventilatory insufficiency, home ventilator, medical electrical equipment, alarm systems, accessories, IEC 60601, ISO 20417.
Технические детали
- Технический комитет
- VAZ - Healthcare
- SKU
- SIST EN ISO 80601-2-80:2024
Похожие стандарты
Стандарты, упомянутые в описании
ISO 80601-2-80:2024
ДействующийMedical electrical equipment - Part 2-80: Particular requirements for basic safety and essential performance…
Overview ISO 80601-2-80:2024 is an international standard defining particular requirements for the basic safety and essential performance of ventilatory support equipment for ventilatory insufficienc…
EN ISO 20417:2026
ДействующийMedical devices - Information to be supplied by the manufacturer (ISO 20417:2026)
Overview EN ISO 20417:2026, titled Medical devices - Information to be supplied by the manufacturer (ISO 20417:2026), is a European and international standard developed jointly by CEN and ISO. This s…
IEC 60601-1:2005
ДействующийMedical electrical equipment - Part 1: General requirements for basic safety and essential performance
Overview IEC 60601-1:2005 (Consolidated Edition 3.1, with Amendment 1) is the international safety standard for medical electrical equipment, defining the general requirements for basic safety and es…
PD ISO/TR 21954:2018
ДействующийGuidance on the selection of the appropriate means of ventilation based on the intended patient, use environm…
ISO 80601-2-13:2022/Amd 1:2026
ДействующийMedical electrical equipment — Part 2-13: Particular requirements for basic safety and essential performance…
Overview ISO 80601-2-13:2022/Amd 1:2026 is an international standard amendment developed by ISO for medical electrical equipment, specifically focusing on anaesthetic workstations. This amendment int…
SIST EN ISO 80601-2-12:2024
ДействующийMedical electrical equipment - Part 2-12: Particular requirements for basic safety and essential performance…
Overview SIST EN ISO 80601-2-12:2024 (identical to EN ISO 80601-2-12:2023 / ISO 80601-2-12:2023) specifies the particular requirements for the basic safety and essential performance of critical care…