Найдено: 37
Overview ISO 3958:1996 - "Passenger cars - Driver hand-control reach" defines three‑dimensional hand‑reach envelopes for passenger‑car driver controls. The second edition (1996) replaces the 1977 edi…
Overview - ISO 3957:2025 (Reaction to fire tests, Parallel panel test) ISO 3957:2025 specifies a large-scale fire test method - the parallel panel test (PPT) - for measuring the heat release rate (HR…
Overview ISO 3952-4:1984, titled "Kinematic diagrams - Graphical symbols - Part 4", is an international standard developed by the International Organization for Standardization (ISO). This part of IS…
Overview ISO 3953:2025 is the latest international standard specifying a standardized method for determining the tap density of metallic powders. Tap density refers to the density of a powder after i…
Overview ISO 3952-1:1981 - "Kinematic diagrams - Graphical symbols - Part 1" defines a system of standardized graphical symbols for kinematic diagrams. Published as the first edition on 1981-12-15 an…
Overview ISO 3959:1977 - "Green bananas - Ripening conditions" defines recommended postharvest ripening protocols for green bananas intended for international trade. The standard describes pre-ripeni…
Overview ISO 3954:2007 - "Powders for powder metallurgical purposes - Sampling" specifies standardized procedures to obtain representative samples of powders used in powder metallurgy and to split th…
Overview ISO 3951-2:2013 specifies an acceptance sampling system of single sampling plans for inspection by variables, indexed by the Acceptance Quality Limit (AQL). Intended for users already famili…
Overview ISO 3950:2016, titled Dentistry - Designation system for teeth and areas of the oral cavity, is an international standard developed by the International Organization for Standardization (ISO…
Overview - ISO 3951-5:2006 (Sequential sampling plans, AQL, known σ) ISO 3951-5:2006 specifies a system of sequential sampling plans indexed by Acceptance Quality Limit (AQL) for inspection by variab…
Overview ISO 3951-3:2007 - Sampling procedures for inspection by variables - Part 3 describes an acceptance sampling system of double sampling schemes indexed by acceptance quality limit (AQL) for lo…
Overview ISO 3953:2011 specifies a standardized laboratory method for determining the tap density of metallic powders - the density of a powder after it has been mechanically tapped into a container…
Overview - ISO 3951-6:2023 (Sampling procedures for inspection by variables) ISO 3951-6:2023 specifies single sampling plans for inspection by variables indexed by limiting quality (LQ), intended for…
Overview ISO 39511:2018 - Sequential sampling plans for inspection by variables for percent nonconforming (known standard deviation) - specifies sequential sampling plans and procedures for inspectin…
Overview ISO 3952-2:1981 - Kinematic diagrams - Graphical symbols - Part 2 defines a standardized system of graphical symbols for kinematic diagrams, focusing on friction and gear mechanisms and cam…
Overview ISO 3952-3:1979 is an International Organization for Standardization (ISO) standard that defines a system of graphical symbols for kinematic diagrams, specifically covering Geneva and ratche…
Overview ISO 3951-1:2022 - Sampling procedures for inspection by variables specifies single sampling plans indexed by the Acceptance Quality Limit (AQL) for lot‑by‑lot inspection of a single measurab…
Overview ISO 3951-4:2011 - "Sampling procedures for inspection by variables - Part 4: Procedures for assessment of declared quality levels" specifies variable-based sampling plans and procedures to a…
1 Scope This International Standard specifies a method for the determination of tap density, i.e. the density of a powder that has been tapped into a container under specified conditions.
What is ISO 3951 ‑ 1 about? ISO 3951 ‑ 1 is the first part of the multi-series international standard that focuses on single sampling plans indexed by acceptance quality limit with inspection for a s…